How to Remove Mold from Drywall

Not only does mold on your interior walls appear bad, but it can also put your family’s health in danger. Its presence may also point to a more serious issue in your home—water infiltration—depending on the quantity and location.

We’ll concentrate on finding a mold solution for this job. There are two solutions: 1. Manage the moisture, and 2. Get rid of the mold. The latter is frequently accomplished with some bleach, water, and some elbow grease, whilst the former can require a more thorough technique depending on the circumstance.

Steps for Removing Mold from Drywall

The following are some steps you can take to remove mold from drywall.

  • Stop the Moisture Source

You must stop the source of moisture before you can begin to remove the mold from your drywall. You need to remedy the issue, whether it’s a leaky window or pipe, a roofing problem, or water vapor seeping through a concrete floor. If not, mold will begin to form nearly right away after you’ve finished removing it.

  • Collect Your Drywall Mold Removal Tools

Mold removal will surely stir up spores and release them into the air. You can lessen your exposure to those spores by donning long sleeves and pants, rubber gloves, a respirator mask, and a pair of safety glasses.

  • Time for a Choice: Save or Discard?

In certain cases, tearing out moldy drywall is safer, more efficient, and quicker than cleaning it. If the surface of your drywall feels mushy to the touch, the mold and moisture have compromised the structural integrity of the material. In this situation, it would be preferable to take off the drywall, treat the framing underneath for mold, let it dry, and then start over.

  • Drywall surface mold should be removed

You’ll need to deal with the surface spores first if you choose to remove the mold from your drywall by yourself. Use your shop vacuum with a HEPA filter to thoroughly clean the surface. To guarantee you’re breaking up the spores and removing as many as you can, use a brush attachment.

  • Remove the mold

You can start destroying the mold once you’ve eliminated the majority of the surface spores. You can use a variety of products for this phase, including:

Baking soda, white vinegar, and water in a 2:1:1 ratio with 3% hydrogen peroxide are used to control consortium mold.
Contrary to common perception, bleach is not always successful in removing mold. Although it can destroy surface spores, the roots won’t be significantly harmed.

Spray or brush your solution on the drywall and let it sit for 10 minutes before using a medium-bristled brush to scrub the surface in a circular motion.

When using Consortium, you should first wait for the surface to dry completely before dampening the brush with additional Concorbium and beginning to brush.

Any residue that might remain after brushing should be quickly cleaned up with a home cleaning wipe.

  • Fan the wall to dry it out

The next step is to let the wall to dry after the spores have been destroyed and residue removed. Position a box fan so that it faces the wall directly. In order to ensure that the wall dries fully, let it run for 24 hours.

  • Cover the Stains

Your drywall may start to seem discolored after 24 hours. Most of the time, this staining is just a minor stain that can be removed, not mold growing again. You can use a mold-killing primer, such as this one from Zinsser, to be safe. These primers produce a protective fungicidal covering that can hide the stains while also eliminating any stray spores.

You can cover the area with mold-resistant paint like these offerings from JH Wall Paints once the stains are no longer discernible. The alkaline pH values of these paints produce a hostile environment for molds and germs.

  • Reduce the humidity

Future mold growth may be encouraged by a humid environment. Make every effort to keep the area dry and mold-free by reducing humidity. To prevent mold from forming in other areas, use a dehumidifier to maintain the humidity between 30 and 50 percent.

By following these instructions, you may get rid of mold from your drywall surfaces and prevent it from returning.

Leave a Reply

Your email address will not be published. Required fields are marked *