How to Install Landscaping Edging?

Do you want to change the outlook of your garden, making it beautiful? Or, are you trying to implement new landscape design ideas for your space? Then, this article is a must-read for you.

Landscape edging can turn a dull space into a charming one, bringing peace of mind. But how to install landscaping edging? You can take professional landscaping services, but here we’ve focused on the DIY process to save you money and time.

In this article, you will find some easy ways of landscape edging along with the working procedure. So, keep reading till the end to enlighten yourself.

Plastic yard edging is utilized to recognize a nursery bed from the remainder of the grass, making your nursery look perfect and clean! To put the yard edging, burrow a channel around the nursery bed and remove any roots. Then, at that point, set the edging by filling the channel in with soil once more, and installing edging stakes.

3 ways to install landscaping Edging

There are 3 ways through which you can install landscape edging which are:

  1. Plastic edging
  2. Brick edging
  3. Metal edging

Let’s look into the steps of these different edgings.

5 steps of plastic edging

Plastic edging brings an aesthetic look to your garden. However, it would help if you put in a little effort to get the best results.

There are 5 steps of plastic edging, which are:

  1. Mark your area
  2. Dig your trench
  3. Place the long strips
  4. Backfill your area
  5. Place the short pieces

Let’s dig deep into the steps!

Step 1: Mark your area

First, you need to mark your area with an old hose. Then, layout the different sizes that you need to spray-paint them. However, make sure you are painting the edge of your area.

Step 2: Dig your trench

Now, start to dig your trench on your painted line.

However, there are specific sizes that you need to maintain. The width should be around four to six inches and depth of about three to inches.

Later, take the sand and fill the ground about 1 inch by leveling it properly. Finally, dig the soil loosely to start your landscaping.

Step 3: Place the long strips

When you think of plastic landscaping, make sure your plastics are long and flexible. It would help you in the process of horizontally trenching them.

Now, take a hammer to place the long strips three to four inches on the ground. However, all the strips should be five feet apart with a 45-degree angle.

For having the best outcome, the width of plastic edging needs to be five inches with .5 inches of the ground.

Step 4: Backfill your area

Now, use your garden soil to backfill your area. Once you fill the site, you will realize that the edgings are upright in place. Finally, it would help if you watered the bottom so that the cement sits properly on your edge.

Step 5: Place the short pieces

In the end, you need to interlock all the panels with the short pieces. Now, take one short part to connect it with another one. So, continue with this process till you cover the whole trench.

4 steps of brick edging

Brick edging brings an edgy tone to your garden. However, brick edging is easier than plastic edging.

The 4 steps of brick edging are:

  1. Spread out your bed
  2. Set up 2 stakes
  3. Insert your bricks
  4. Cut the bricks

Let’s look into the steps.

Spread out your bed

First, you need to spread out your bed. So, you need to dig out the borders and fill them with soil.

However, it is necessary to use a spade to dig out the area. Finally, flatten the soil by using the bottom of a trench.

Set up 2 stakes

Most hammer stakes are around four to six inches long in the bottom of a trench. Next, connect one stake with the other by hooking the mason’s line.

Now, you need to hook it with other stakes by holding the twine. Finally, place a brick on the line by properly leveling the yarn.

Insert your bricks

You can use a mason line to place the bricks properly. However, you need to complete the process very carefully.

Once you insert a brick, make sure you are putting enough soil and rocks to secure them. Finally, water the area to help cement and brick get attached.

Cut the bricks

Some areas tend to be shorter in size, so you need to cut the bricks.

In such cases, first, you need to measure the area and then mark the brick. Later, place the marked brick on a chisel to break it properly. Finally, you can use the left pieces for the last part.

3 steps of metal edging

Metal edging gives an elegant tone to your garden. However, metal edging is a practical way out for your garden.

There are 3 steps of metal edging, which are:

  1. Test your soil
  2. Insert metal edging
  3. Hammer the metal stakes

Let’s see how these 3 steps of metal edging works!

Test your soil

At first, you need to dig out the soil in your area by using a shovel. However, it is important to understand the ground by touching them.

If you think it is soft, then you can push the metals. On the other hand, if the soil is hard, it is necessary to dig the trench.

Insert metal edging

From the ground, you need to insert the metal edging two to three inches below. The soil can be soft or hard.

If it’s soft, you can use wood to insert the metal. On the other hand, if it’s hard, you need to dig the soil into inserting the metal.

Additionally, make sure that the metal edgings overlap each other by 1 foot to get connected. You can choose metal edging as they are very robust and can be easily curved.

Hammer the metal stakes

Finally, it would help if you secured the metal stake by hammering them.

It is important to hammer the metal stakes for four to six inches. On the other hand, you need to keep the edging out of about two to three feet.

Nevertheless, the metal edging of the garden should be with slots or anchors—finally, water the area to secure the metal edge.


To sum up, there are three types of landscape edging – plastic, brick, and metal.

However, their steps are very different from each other. Additionally, all of these edgings look different when they are inserted properly.

A divider an excess help – either from being filled with all-around stuffed soil or reinforced by mortar.

Stake-driven edging incorporates large numbers of the engineered items accessible in stores, for example, rolls of flexible plastic or steel. To install this item, you’ll need to cut a line in the dirt where the edging will be embedded, place it in the ground at the true profundity, and secure it with a stake that is pounded corner to corner through the item and into the ground at the appropriate point (adhere to guidelines included with your item for careful estimations and strategies.

If you think these processes look tough, it would be best if you take professional help. There are very firms that can help you out in the processes.

In this article, you will find some easy ways of landscape edging along with the working procedure. So, keep reading till the end to enlighten yourself.

So, you can sit back and hand the edging to the professionals!

See more: How Can I Get US Students Email Lists For Marketing Purposes?

Lisa Vincent
Lisa Vincent


Leave a Reply

Your email address will not be published. Required fields are marked *